Road Guardrail beam-manufacture,factory,supplier from China

On April 2, 2023, Mr. mico found FORST on the website. Two weeks later, he formally signed an agreement to reach a cooperation. Mr. mico has been engaged in the guardrail beam business in Brunei for 12 years, and has a deep understanding of guardrail beam products. There are strict acceptance criteria for quality.The road for this maintenance guardrail project belongs to the national trunk line of Brunei.

1. The guardrail beam is the main form of semi-rigid guardrail. It is a continuous structure composed of corrugated steel guardrail beam that are spliced together and supported by columns. It uses the deformation of soil foundation, columns, and guardrail beam to absorb collision energy, force out of control vehicles to change direction, return to normal driving direction, prevent vehicles from rushing out of the road, protect vehicles and passengers, and reduce losses caused by accidents.2.

(1) The corrugated guardrail beam should not have obvious torsion, nor should it be welded or lengthened, and the end burrs must be removed. The layout of columns is based on the control points on the highway, and the spacing between columns is adjusted appropriately according to the measurement distance; The installation of columns should be consistent with the design drawings and coordinated with the road alignment.

1. The guardrail beam  is located in the middle of road development, which can effectively prevent the occurrence of a second utilization collision when a vehicle loses control and runs into the opposite lane.2. Guardrail beam is a semi steel protective device with good toughness, which forces the vehicle to return to the normal route when it collides.3. Guardrail beam can effectively alleviate the harm that collisions can cause to drivers. Guardrail beam have good toughness and are not easy to break.

1. Separation function: Guardrail beam separate motor vehicles, non motor vehicles, pedestrians, and traffic spaces, and analyze the longitudinal horizontal separation of roads on cross-sections, allowing motor vehicles, non motor vehicles, and pedestrians to move in separate lanes, improving the safety of traffic development in China and improving traffic management order.2. Obstacle effect: Traffic obstacles can hinder bad traffic behavior, such as pedestrians, bicycles, or motor vehicles attempting to cross the road.

Guardrail beam not only has the advantages of good impact resistance, low cost, long service life, and higher safety, but the beautiful design is also coordinated with the highway environment, improving the overall aesthetics of the road.In recent years, with the improvement of road safety awareness and vehicle speed, the design and construction requirements for guardrail beam has also been constantly increasing.In addition, the reuse of guardrail beam has also become a focus of attention.

Firstly, guardrail beam should have sufficient strength and stiffness to withstand the impact force of vehicle collisions, prevent vehicles from crossing or collapsing through guardrail beam and thus avoid the occurrence of secondary accidents.Secondly, guardrail beam should have good energy absorption performance, which can absorb the kinetic energy of vehicle collisions and reduce injuries to vehicles and passengers.In addition, guardrail beam should also have good line of sight guidance function, which can coordinate with the road alignment, provide clear driving direction indications, and

Macy is a road construction contractor in Laos, and has been purchasing road guardrail beams from FORST for 3 years. This is the rendering of the installation of the guardrail beams that has been fed back to us recently. It will be the rainy season in Laos soon. The total project size is 5,300 meters, and all installations must be completed before the rainy season comes.Guardrail beams are matched with round post, each guardrail beam is equipped with reflective cursors, and each guardrail beam post is affixed with reflective stickers.

Basic requirements for highway guardrail: Wave beam and rigid guardrail products should comply with relevant document standards such as "Highway Wave Beam Rigid Guardrail" and "Three Road Beam Guardrail". The installation of guardrail columns, corrugated steel, anti blocking blocks, and brackets should meet the requirements of design and construction. To ensure the overall strength of highway guardrail, the compactness of the shoulder and central divider should not be lower than the design value.

① Inspection method: When preparing for the inspection, the inspection personnel should carefully inspect the technical condition of the inspection vehicles and communication equipment, verify the handover records of the inspection, and develop an inspection plan. During the inspection of guardrail beam, vehicles should be illuminated according to regulations, and the speed should generally be controlled at 40km/h. Pay attention to the changes in the technical conditions of the highway and keep records of the inspection of key structures and road sections.